DIY Tub Installation.
DIY Tub Installation.
Blog Article
The article author is making several good points regarding Installing A Bathtub overall in the content which follows.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently available, the task can relocate quickly; if you have to open up a wall to get rid of the old tub and also place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and embeded in the new one. See to it you have certified on your own for the job as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly help you mount a new bath tub in your restroom if you have currently bought a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools and also material list ought to consist of the following:
Planning for the Installation
To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that content about A Step-by-Step Guide to Installing a Bathtub when surfing around the web. Sharing is nice. You just don't know, you might be helping someone out. Thanks so much for going through it.
Call Today Report this page